II.

Transmitter

Essential components of a radio transmitter include an oscillation generator for converting commercial electric power into oscillations of a predetermined radio frequency; amplifiers for increasing the intensity of these oscillations while retaining the desired frequency; and a transducer for converting the information to be transmitted into a varying electrical voltage proportional to each successive instantaneous intensity. For sound transmission a microphone is the transducer; for picture transmission the transducer is a photoelectric device. See Facsimile Transmission; Television.

Other important components of the radio transmitter are the modulator, which uses these proportionate voltages to control the variations in the oscillation intensity or the instantaneous frequency of the carrier, and the antenna, which radiates a similarly modulated carrier wave. Every antenna has some directional properties, that is, it radiates more energy in some directions than in others, but the antenna can be modified so that the radiation pattern varies from a comparatively narrow beam to a comparatively even distribution in all directions; the latter type of radiation is employed in broadcasting.

The particular method of designing and arranging the various components depends on the effects desired. The principal criteria of a radio in a commercial or military airplane, for example, are light weight and intelligibility; cost is a secondary consideration, and fidelity of reproduction is entirely unimportant. In a commercial broadcasting station, on the other hand, size and weight are of comparatively little importance; cost is of some importance; and fidelity is of the utmost importance, particularly for FM stations (see Frequency Modulation); rigid control of frequency is an absolute necessity. In the U.S., for example, a typical commercial station broadcasting on 1000 kHz is assigned a bandwidth of 10 kHz by the Federal Communications Commission, but this width may be used only for modulation; the carrier frequency itself must be kept precisely at 1000 kHz, for a deviation of one-hundredth of 1 percent would cause serious interference with even distant stations on the same frequency.

A.

Oscillators

In a typical commercial broadcasting station the carrier frequency is generated by a carefully controlled quartz-crystal oscillator. The fundamental method of controlling frequencies in most radio work is by means of tank circuits, or tuned circuits, that have specific values of inductance and capacitance, and that therefore favor the production of alternating currents of a particular frequency and discourage the flow of currents of other frequencies (see Electric Circuit; Resonance). In cases where the frequency must be extremely stable, however, a quartz crystal with a definite natural frequency of electrical oscillation is used to stabilize the oscillations (see Crystal). The oscillations are actually generated at low power by an electron tube and are amplified in a series of power amplifiers that act as buffers to prevent interaction of the oscillator with the other components of the transmitter, because such interaction would alter the frequency. The crystal is shaped accurately to the dimensions required to give the desired frequency, which may then be modified slightly by adding a condenser to the circuit to give the exact frequency desired. In a well-designed circuit, such an oscillator does not vary by more than one-hundredth of 1 percent in frequency. Mounting the crystal in a vacuum at constant temperature and stabilizing the supply voltages may produce a frequency stability approaching one-millionth of 1 percent. Crystal oscillators are most useful in the ranges termed very low frequency, low frequency, and medium frequency (VLF, LF, and MF). When frequencies higher than about 10 MHz must be generated, the master oscillator is designed to generate a medium frequency, which is then doubled as often as necessary in special electronic circuits. In cases where rigid frequency control is not required, tuned circuits may be used with conventional electron tubes to generate oscillations up to about 1000 MHz, and reflex klystrons are used to generate the higher frequencies up to 30,000 MHz. Magnetrons are substituted for klystrons when even larger amounts of power must be generated. See Electronics.

B.

Modulation

Modulation of the carrier wave so that it may carry impulses is performed either at low level or high level. In the former case the audio-frequency signal from the microphone, with little or no amplification, is used to modulate the output of the oscillator, and the modulated carrier frequency is then amplified before it is passed to the antenna; in the latter case the radio-frequency oscillations and the audio-frequency signal are independently amplified, and modulation takes place immediately before the oscillations are passed to the antenna. The signal may be impressed on the carrier either by frequency modulation (FM) or amplitude modulation (AM).

The simplest form of modulation is keying, interrupting the carrier wave at intervals with a key or switch used to form the dots and dashes in continuous-wave radiotelegraphy.

The carrier wave may also be modulated by varying the amplitude, or strength, of the wave in accordance with the variations of frequency and intensity of a sound signal, such as a musical note. This form of modulation, AM, is used in many radiotelephony services including standard radiobroadcasts. AM is also employed for carrier current telephony, in which the modulated carrier is transmitted by wire, and in the transmission of still pictures by wire or radio. See Broadcasting, Radio and Television.

In FM the frequency of the carrier wave is varied within a fixed range at a rate corresponding to the frequency of a sound signal. This form of modulation, perfected in the 1930s, has the advantage of yielding signals relatively free from noise and interference arising from such sources as automobile-ignition systems and thunderstorms, which seriously affect AM signals. As a result, FM broadcasting is done on high-frequency bands (88 to 108 MHz), which are suitable for broad signals but have a limited reception range.

Carrier waves can also be modulated by varying the phase of the carrier in accordance with the amplitude of the signal. Phase modulation, however, has generally been limited to special equipment.

The development of the technique of transmitting continuous waves in short bursts or pulses of extremely high power (see Radar) introduced the possibility of yet another form of modulation, pulse-time modulation, in which the spacing of the pulses is varied in accordance with the signal.

The information carried by a modulated wave is restored to its original form by a reverse process called demodulation or detection. Radio waves broadcast at low and medium frequencies are amplitude modulated. At higher frequencies both AM and FM are in use; in present-day commercial television, for example, the sound may be carried by FM, while the picture is carried by AM. In the superhigh-frequency range (above the ultrahigh-frequency range), in which broader bandwidths are available, the picture also may be carried by FM.

Digital radio (also called HD or high-definition radio) processes sounds into patterns of numbers instead of into patterns of electrical waves and can be used for both FM and AM broadcasts. The sound received by a radio listener is much clearer and virtually free from interference. The signals can be used to provide additional services, multiple channels, and interactive features. Satellite radio is also a form of digital radio but the signal is broadcast from communication satellites in orbit around Earth and not from local broadcast towers.

C.

Antennas

The antenna of a transmitter need not be close to the transmitter itself. Commercial broadcasting at medium frequencies generally requires a very large antenna, which is best located at an isolated point far from cities, whereas the broadcasting studio is usually in the heart of the city. FM, television, and other very-high-frequency broadcasts must have very high antennas if appreciably long range is to be achieved, and it may not be convenient to locate such a high antenna near the broadcasting studio. In all such cases, the signals may be transmitted by wires. Ordinary telephone lines are satisfactory for most commercial radio broadcasts; if high fidelity or very high frequencies are required, coaxial or fiber optic cables are used (see Cable, Electric).